網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.vitagia.com

常見問題

當前位置:首頁 - 新聞中心 - 常見問題 - 氣液增壓機的上模安裝要注

氣液增壓機的上模安裝要注意什么?

發布時間:2021-11-10 16:56:46   發布人:http://www.vitagia.com
上模固定板的雙T形槽成60°,用模柄插入卡頭安裝,或采用壓板或螺栓固定上模。具體分為以下類型:
The double T-shaped groove of the upper die fixing plate is 60 & deg;, Insert the die handle into the clamp for installation, or fix the upper die with pressing plate or bolt. It can be divided into the following types:
主軸帶卡頭安裝,不防轉,無總行程調節機構:
The spindle is installed with a chuck, without anti rotation and no total stroke adjustment mechanism:
此類結構主要用于壓頭重量較輕(3KG以下)且無需防轉功能,無需總行程調節的情況。
This kind of structure is mainly used when the weight of the indenter is light (below 3kg) and there is no need for anti rotation function and total stroke adjustment.
主軸帶卡頭,雙導柱防轉機構,無總行程調節機構:
The main shaft is equipped with chuck, double guide post anti rotation mechanism, and there is no total stroke adjustment mechanism:
此類結構主要用于壓頭重量較輕(3KG以下)且需要防轉功能,但無需總行程調節功能的情況。
This kind of structure is mainly used when the weight of the indenter is light (below 3kg) and the anti rotation function is required, but the total stroke adjustment function is not required.
氣液增壓泵
主軸帶卡頭,雙導柱防轉機構及總行程調節機構:
The main shaft is equipped with chuck, double guide post anti rotation mechanism and total stroke adjustment mechanism:
此類結構主要用于壓頭重量較重(3KG以上),采用卡頭和模柄安裝的情況。
This kind of structure is mainly used when the weight of the indenter is heavy (more than 3kg) and the clamp head and die handle are used for installation.
無卡頭帶上模板,雙導柱防轉機構及總行程調節機構:
No card head, with upper formwork, double guide post anti rotation mechanism and total stroke adjustment mechanism:
此類結構主要用于上模板安裝,對導向精度和剛性的要求相對較低的情況。
This kind of structure is mainly used for the installation of upper formwork, and the requirements for guiding accuracy and rigidity are relatively low.
無卡頭帶上模板,四導柱防轉機構及總行程調節機構:
No card head, with upper formwork, four guide pillar anti rotation mechanism and total stroke adjustment mechanism:
此類結構主要用于上模板安裝,對導向精度和剛性的要求相對較高的情況。
This kind of structure is mainly used for the installation of upper formwork and has relatively high requirements for guiding accuracy and rigidity.
新聞推薦:
氣體增壓泵在工廠使用要注意哪些優勢? 2021-12-09
氣體增壓泵空氣增壓泵可以使用多長時間? 2021-11-30
氣液增壓泵施工步驟是先怎么操作? 2021-11-18
氣液增壓機的上模安裝要注意什么? 2021-11-10
氣體增壓泵與氣液增壓泵的區別! 2021-10-20
為什么氣體增壓泵經常突然不工作了? 2021-10-13
氣體增壓設備一般的組成部分是? 2021-10-06
冬季來臨,氣動增壓泵容易出那些問題? 2021-09-27
想要降低氣動空氣增壓泵系統的溫度能采... 2021-09-17
氣體增壓泵與氣液增壓泵的區別 2021-09-10

13188935873

qq

黑人巨茎大战俄罗斯美女